Custom manufacturing and worldwide export — request a quote: +90 532 689 21 46
Bayrakdoor Steel Doors
Bayrakdoor

Two-Section Panel Anthracite Gray Villa Door BD-TR75

Product CodeBD-TR75

An anthracite paneled leaf with wrought iron detailed glass at the sides. Product code: BD-TR75. Made to measure after a free on-site survey.

Leaf construction
single leaf + double sidelight
Color / finish
anthracite grey
Handle
gold knocker and gold handle
Design language
classic villa
Share this model

Pre-Order & Price Request

This model is made to measure. Leave your request and we'll call you to arrange a site survey.

Product codeBD-TR75

This is here to block automated submissions — it only takes a second.

  • Survey and measurement are free
  • Same-day response
  • Made in our own factory
  • Lifetime manufacturing warranty
Download this model's PDF spec sheet
Worldwide shipping & export
Made in our own factory
Lifetime manufacturing warranty

The BD-TR75 two-section panel anthracite gray villa door is built as an anthracite paneled leaf with wrought iron detailed glass at the sides. Like every door we make, this model is made to measure; no ready-made leaf is supplied from stock. The catalog finish is an anthracite gray tone.

Product Code: BD-TR75

Leaf and Glass Layout

The layout is a single leaf with twin side glass. The leaf surface is worked as a two-section panel. The catalog color is an anthracite gray tone.

The glazing is resolved as side glass with wrought iron detailing. Hardware is a gold knocker and a gold handle. Cladding and hardware are not fixed; it can be produced with any of the alternatives on the cladding options page.

Its design language is best described as classic villa.

Who Is This Model For?

It is chosen primarily for villa entrances and residence apartments. Since the side sections widen the opening, it suits wide-fronted entrances rather than narrow ones — and it brings daylight into the hall. We compare where a villa door and a building entrance door part ways on the villa door vs. building entrance door page.

From Measurement to Installation

Measurements are taken from the door opening, not the existing leaf; the how measurements are taken page walks through it step by step. Frame, sheet thickness, infill, and lock values are listed in the specification table below. Sheet choices are compared on the galvanized or DKP sheet page, and lock alternatives on the lock systems page. After installation, our care and lifespan and warranty and service terms apply.

Frequently Asked Questions

How much does the BD-TR75 model cost?

There is no fixed price — since every leaf is built to size, the total depends on the dimensions, the cladding, and the lock you choose. After the survey we send a written, itemized quote. The line items are detailed on the steel door prices page.

Can the BD-TR75 be produced in a different color?

Yes, the color is not fixed. It appears anthracite gray in the catalog, but the cladding is decided per project; on the cladding options page we cover which surface works best where.

Can the glass on the BD-TR75 be changed?

Yes. The glass shown is this model's catalog finish; provided Şişecam 5+5 mm laminated glass is used, it can be produced in different colors and patterns. A glass-free version is also possible.

How does the measurement stage work when ordering the BD-TR75?

We take the measurements during the survey; nothing is required on your part. Measurements are taken from the door opening, not the existing leaf — the method is explained on the how measurements are taken page.

How do I order the BD-TR75 model?

You can fill out the pre-order form on our site or reach us at 0532 689 21 46. Mentioning product code BD-TR75 in your request speeds things up. You can browse our other villa steel doors on the villa steel door models page.

Specifications

Product codeBD-TR75
CategoryVilla Steel Door Models
Leaf constructionsingle leaf + double sidelight
Color / finishanthracite grey
Surface patterntwo-section panel
Handlegold knocker and gold handle
Design languageclassic villa
Access systemOptional card or keypad entry
Sheet thicknessFrame 2 mm (0.079"), leaf 1.5+1.5 mm (0.118" total) DKP steel sheet (Ereğli A1)
FrameEreğli A1 grade 2 mm (0.079") DKP steel sheet, omega-bent
Frame reinforcementLock and hinge areas reinforced with 3 mm (0.118") DKP steel sheet
LeafEreğli A1 grade 1.5 mm (0.059") + 1.5 mm (0.059") omega-bent, monoblock-reinforced pan system
Leaf reinforcementLock and hinge area reinforced with 3 mm (0.118") angle bar
Leaf thicknessBare metal 70 mm (2.76") — 90 mm (3.54") in total
Infill80 kg/m³ rock wool
Lock surroundintegrated with 1 mm (0.039") grade 304 stainless steel
Hinge3 adjustable 20 mm (0.787") ball-bearing pin hinges
Hinge reinforcement5 mm (0.197") thick flat bar
Fixed pin5 units on the hinge side, 20 mm (0.787") diameter
GasketSilicone-based rubber gasket on 3 sides of the frame, 4 sides of the leaf (insect-, dust- and airtight)
Surface finish10 mm (0.394") Camsan first-grade iroko
Finish optionsPowder coating, natural wood, marine plywood, iroko wood or composite compact laminate
VarnishPolyurethane infill, 90-micron coverage rating
PolishAkzo Nobel
Accessoriesfirst-grade 304 stainless steel or 316 Häfele stainless brass (depending on climate conditions)
InstallationOne-piece inner/outer frame, clamp-grip jointing, fastened with M8 bolts
Frame-to-wall gap1 cm (0.394"), filled with polyurethane foam
ProductionManufactured to custom on-site measurements
WarrantyUnlimited coverage for manufacturing defects — 2-year official warranty certificate
Lock systemOptional hook-bolt, monoblock or central — Italian Mottura or Mul-T-Lock
Glass sectionsidelights with wrought iron detailing
Glass typeŞişecam 5+5 mm (0.394" total) laminated glass (impact resistant)

Frequently Asked Questions

What is the lead time for a custom villa door?

Production takes 20-25 days from the day the specification is approved. Custom detailing — carved cladding, oversized leaves, special glass — can extend that, and we confirm the date in writing before starting. Ocean freight time to the destination port is added on top.

How are steel doors packaged for sea freight export?

Each door is crated in a wooden case built to its own dimensions, with edge protection and corner blocks, then strapped to prevent movement inside the container. Full container loading is used for project quantities; single doors and small orders ship as groupage cargo.

What measurements do you need to quote?

The width, height and wall thickness of the rough opening, in millimetres or in inches — whichever your drawings use. Photographs of the opening from inside and outside help us confirm the swing direction and the frame detail. No site visit is needed.

Can you manufacture to imperial (inch) dimensions?

Yes. An opening given as 36 x 80 inches is manufactured to that dimension directly. Nothing is converted to a nearest metric size and rounded, so the door arrives at the size your drawing specifies.

Who installs the door at the destination?

Your own contractor. Every shipment includes an installation drawing and the frame fixing set, and the frame is designed to be set into the opening without special tooling.

What export documents travel with the shipment?

Commercial invoice, packing list and certificate of origin, plus whatever else the customs broker at the destination requires. Documentation is prepared before the container leaves the factory.

You May Also Like

Before you decide

Pages where we cover the technical questions most often asked about this model:

classic design

More Models in This Style

View All

anthracite and grey

Models in the Same Color Family

View All