Custom manufacturing and worldwide export — request a quote: +90 532 689 21 46
Bayrakdoor Steel Doors
Bayrakdoor

Clean-Lined Light Wood Pivot Steel Door TR309

Product CodeTR309

Narrow, extra-tall light wood pivot leaf set between stone and glass facades. Product code: TR309. Made to measure after an on-site survey.

Leaf construction
pivot single leaf (narrow and tall)
Color / finish
light wood
Handle
recessed handle
Design language
modern pivot
Share this model

Pre-Order & Price Request

This model is made to measure. Leave your request and we'll call you to arrange a site survey.

Product codeTR309

This is here to block automated submissions — it only takes a second.

  • Survey and measurement are free
  • Same-day response
  • Made in our own factory
  • Lifetime manufacturing warranty
Download this model's PDF spec sheet
Worldwide shipping & export
Made in our own factory
Lifetime manufacturing warranty

A narrow, extra-tall light wood pivot leaf set between stone and glass facades. Listed in our catalog under code TR309. There is no standard size — the door opening is measured during the survey and production follows that measurement. The finish shown in the photo is light wood cladding.

Product Code: TR309

Surface and Glazing

Produced as a pivot single leaf, narrow and tall. The surface is a flat wood face. The surface is finished in light wood.

The glazing takes the form of glass panels to the sides. It is completed with a recessed handle. Cladding and hardware are not fixed; the door can be produced with any of the alternatives on our cladding options page.

Its design language is defined as modern pivot.

Suitable Entrances

It is chosen primarily for office and plaza entrances and hotel and showroom entrances. The monolithic leaf presents an uninterrupted surface from the outside. Since the load rests on the floor rather than on hinges, the leaf can be far wider and thicker. Because it needs swing clearance, it does not suit narrow entrances that open directly onto stairs; the conditions are listed on our when to choose a pivot door page.

From Measurement to Installation

We take the measurements during the survey — based on the door opening, not the existing leaf; the method is explained on our how to measure page. You will find this model's frame, leaf and lock values in the table below; the lock systems and galvanized or DKP sheet steel pages detail the options. Maintenance steps that extend the door's life are on the care and lifespan page, and the coverage itself on the warranty and service page.

Frequently Asked Questions

How much does the TR309 model cost?

The price cannot be quoted before measuring. The opening's dimensions and your cladding, glass and lock choices directly affect the total; the survey is free and is followed by an itemized quote. See steel door prices for details.

Can I order this model in a color other than light wood?

Yes — the color is not fixed. The catalog shows light wood, but the cladding is decided per project; on our cladding options page we cover which surface works best where.

Can the glass pattern be different?

Yes. The glass shown is this model's catalog finish; it can be produced in different colors and patterns, provided Şişecam 5+5 mm laminated glass is used. A glassless version is also possible.

How is the TR309 measured?

Measuring is our job. We take the clear width of the opening, the height from the finished floor and the wall thickness; details on our how to measure page.

How do I get a quote for the TR309?

You can fill out the pre-order form on our site or reach us at 0532 689 21 46. Mentioning product code TR309 in your request speeds things up. You can browse other pivot steel door models on our pivot steel door models page.

Specifications

Product codeTR309
CategoryPivot Steel Door Models
Leaf constructionpivot single leaf (narrow and tall)
Color / finishlight wood
Surface patternplain wood surface
Handlerecessed handle
Design languagemodern pivot
MechanismFloor- and ceiling-mounted pivot (rotating) mechanism
Rotation systemFloor and ceiling bearings — no conventional hinges used
Load transferLeaf weight is transferred to the floor, not the frame
Rotation axisDetermined per project based on leaf width (central or offset)
Floor preparationPreparation is required where the bottom bearing sits — assessed during site survey
Required clearanceClearance is needed in both directions, as the leaf swings both inward and outward
Maximum leafCustom project-based sizing — tall and wide leaf production
Sheet thicknessFrame 2 mm (0.079"), leaf 1.5+1.5 mm (0.118" total) DKP steel sheet (Ereğli A1)
FrameEreğli A1 grade 2 mm (0.079") DKP steel sheet, omega-bent
Frame reinforcementLock area and bearing seats reinforced with 3 mm (0.118") DKP steel sheet
LeafEreğli A1 grade 1.5 mm (0.059") + 1.5 mm (0.059") omega-bent, monoblock-reinforced pan system
Leaf reinforcementLock area and pivot shaft surround reinforced with 3 mm (0.118") angle bar
Leaf thicknessBare metal 70 mm (2.76") — 90 mm (3.54") in total
Infill80 kg/m³ rock wool
Lock surroundintegrated with 1 mm (0.039") grade 304 stainless steel
GasketSilicone-based rubber gasket on 3 sides of the frame, 4 sides of the leaf (insect-, dust- and airtight)
Surface finish10 mm (0.394") Camsan first-grade iroko
Finish optionsPowder coating, natural wood, marine plywood, iroko wood or composite compact laminate
VarnishPolyurethane infill, 90-micron coverage rating
PolishAkzo Nobel
Accessoriesfirst-grade 304 stainless steel or 316 Häfele stainless brass (depending on climate conditions)
InstallationInstalled by aligning the floor and ceiling bearings; one-piece frame, fixed with M8 bolts
Frame-to-wall gap1 cm (0.394"), filled with polyurethane foam
ProductionManufactured to custom on-site measurements
WarrantyUnlimited coverage for manufacturing defects — 2-year official warranty certificate
Lock systemOptional hook-bolt, monoblock or central — Italian Mottura or Mul-T-Lock
Glass sectionglass on both sides
Glass typeŞişecam 5+5 mm (0.394" total) laminated glass (impact resistant)

Frequently Asked Questions

What is the lead time for a custom villa door?

Production takes 20-25 days from the day the specification is approved. Custom detailing — carved cladding, oversized leaves, special glass — can extend that, and we confirm the date in writing before starting. Ocean freight time to the destination port is added on top.

How are steel doors packaged for sea freight export?

Each door is crated in a wooden case built to its own dimensions, with edge protection and corner blocks, then strapped to prevent movement inside the container. Full container loading is used for project quantities; single doors and small orders ship as groupage cargo.

What measurements do you need to quote?

The width, height and wall thickness of the rough opening, in millimetres or in inches — whichever your drawings use. Photographs of the opening from inside and outside help us confirm the swing direction and the frame detail. No site visit is needed.

Can you manufacture to imperial (inch) dimensions?

Yes. An opening given as 36 x 80 inches is manufactured to that dimension directly. Nothing is converted to a nearest metric size and rounded, so the door arrives at the size your drawing specifies.

Who installs the door at the destination?

Your own contractor. Every shipment includes an installation drawing and the frame fixing set, and the frame is designed to be set into the opening without special tooling.

What export documents travel with the shipment?

Commercial invoice, packing list and certificate of origin, plus whatever else the customs broker at the destination requires. Documentation is prepared before the container leaves the factory.

You May Also Like

Before you decide

Pages where we cover the technical questions most often asked about this model:

modern design

More Models in This Style

View All

wood tone

Models in the Same Color Family

View All