Horizontal-lamella honey-toned pivot leaf, narrow vertical glazing and a keypad entry panel. Product code: TR314. Manufactured to measure, following an on-site survey.
- Leaf construction
- pivot single leaf + narrow glass
- Color / finish
- honey-toned wood
- Handle
- long horizontal handle
- Design language
- modern pivot
Pre-Order & Price Request
This model is made to measure. Leave your request and we'll call you to arrange a site survey.
- Survey and measurement are free
- Same-day response
- Made in our own factory
- Lifetime manufacturing warranty
The TR314 horizontal-lamella honey-toned wood pivot steel door is produced with a honey-toned horizontal-lamella pivot leaf, narrow vertical glazing and a keypad entry panel. It's manufactured to measure — whatever the width and height of your entrance, the leaf is built to match. The photo shows a honey-toned wood finish.
Product Code: TR314
Surface and Glass Panels
The model is configured as a single pivot leaf with narrow glazing. The surface treatment takes the form of horizontal lamellas with a house number. The color applied is honey-toned wood.
The glazing takes the form of a narrow vertical glass panel. A long horizontal handle is used. The finish shown is the catalog choice — a different cladding can be selected from our cladding options.
The design language is described as modern pivot.
Where Is It Used?
It's most often used in hotel/showroom-entrance and office/plaza-entrance projects. The one-piece leaf presents an unbroken surface when viewed from outside. Because the load rests on the floor rather than on hinges, the leaf can be considerably wider and thicker. Because it needs room to swing, it isn't suited to narrow entrances that open directly onto a staircase — the conditions are laid out on our when to choose a pivot door page.
From Measurement to Installation
Production starts with an on-site measurement. How the door opening is measured is covered on our how measurements are taken page; material choices are compared on our galvanized vs. cold-rolled steel and lock systems pages. The technical specifications for this model are in the table below. The care steps that extend the door's lifespan are on our care and lifespan page, and warranty coverage is on our warranty and service page.
Frequently Asked Questions
How much does TR314 cost?
We can't quote a price before measuring. The size of the door opening, along with the cladding, glass and lock you choose, directly affects the amount; the survey is free, and an itemized quote follows. See our steel door prices page for details.
Can TR314 be made in a different color?
Yes, the color isn't fixed. The catalog shows honey-toned wood, but the cladding is chosen to suit the project; we've written up which finish works best where on our cladding options page.
Can the glass pattern be different?
Yes. The glass shown is this model's catalog finish; it can be produced in a different color and pattern as long as Şişecam 5+5 mm laminated glass is used. A version without glass is also possible.
Do I need to take the measurement myself?
Our survey team measures on site. If you'd still like to understand the process, we've written up the three points we measure on our how measurements are taken page.
How do I get a quote for TR314?
You can fill out the pre-order form on the site, or reach us at 0532 689 21 46. Mentioning the TR314 product code in your request speeds up the process. You can browse other pivot steel door models on our pivot steel door models page.
Specifications
| Product code | TR314 |
| Category | Pivot Steel Door Models |
| Leaf construction | pivot single leaf + narrow glass |
| Color / finish | honey-toned wood |
| Surface pattern | horizontal slats, door number |
| Handle | long horizontal handle |
| Design language | modern pivot |
| Mechanism | Floor- and ceiling-mounted pivot (rotating) mechanism |
| Rotation system | Floor and ceiling bearings — no conventional hinges used |
| Load transfer | Leaf weight is transferred to the floor, not the frame |
| Rotation axis | Determined per project based on leaf width (central or offset) |
| Floor preparation | Preparation is required where the bottom bearing sits — assessed during site survey |
| Required clearance | Clearance is needed in both directions, as the leaf swings both inward and outward |
| Maximum leaf | Custom project-based sizing — tall and wide leaf production |
| Sheet thickness | Frame 2 mm (0.079"), leaf 1.5+1.5 mm (0.118" total) DKP steel sheet (Ereğli A1) |
| Frame | Ereğli A1 grade 2 mm (0.079") DKP steel sheet, omega-bent |
| Frame reinforcement | Lock area and bearing seats reinforced with 3 mm (0.118") DKP steel sheet |
| Leaf | Ereğli A1 grade 1.5 mm (0.059") + 1.5 mm (0.059") omega-bent, monoblock-reinforced pan system |
| Leaf reinforcement | Lock area and pivot shaft surround reinforced with 3 mm (0.118") angle bar |
| Leaf thickness | Bare metal 70 mm (2.76") — 90 mm (3.54") in total |
| Infill | 80 kg/m³ rock wool |
| Lock surround | integrated with 1 mm (0.039") grade 304 stainless steel |
| Gasket | Silicone-based rubber gasket on 3 sides of the frame, 4 sides of the leaf (insect-, dust- and airtight) |
| Surface finish | 10 mm (0.394") Camsan first-grade iroko |
| Finish options | Powder coating, natural wood, marine plywood, iroko wood or composite compact laminate |
| Varnish | Polyurethane infill, 90-micron coverage rating |
| Polish | Akzo Nobel |
| Accessories | first-grade 304 stainless steel or 316 Häfele stainless brass (depending on climate conditions) |
| Installation | Installed by aligning the floor and ceiling bearings; one-piece frame, fixed with M8 bolts |
| Frame-to-wall gap | 1 cm (0.394"), filled with polyurethane foam |
| Production | Manufactured to custom on-site measurements |
| Warranty | Unlimited coverage for manufacturing defects — 2-year official warranty certificate |
| Lock system | Optional hook-bolt, monoblock or central — Italian Mottura or Mul-T-Lock |
| Glass section | narrow vertical glass |
| Glass type | Şişecam 5+5 mm (0.394" total) laminated glass (impact resistant) |
Frequently Asked Questions
What is the lead time for a custom villa door?
Production takes 20-25 days from the day the specification is approved. Custom detailing — carved cladding, oversized leaves, special glass — can extend that, and we confirm the date in writing before starting. Ocean freight time to the destination port is added on top.
How are steel doors packaged for sea freight export?
Each door is crated in a wooden case built to its own dimensions, with edge protection and corner blocks, then strapped to prevent movement inside the container. Full container loading is used for project quantities; single doors and small orders ship as groupage cargo.
What measurements do you need to quote?
The width, height and wall thickness of the rough opening, in millimetres or in inches — whichever your drawings use. Photographs of the opening from inside and outside help us confirm the swing direction and the frame detail. No site visit is needed.
Can you manufacture to imperial (inch) dimensions?
Yes. An opening given as 36 x 80 inches is manufactured to that dimension directly. Nothing is converted to a nearest metric size and rounded, so the door arrives at the size your drawing specifies.
Who installs the door at the destination?
Your own contractor. Every shipment includes an installation drawing and the frame fixing set, and the frame is designed to be set into the opening without special tooling.
What export documents travel with the shipment?
Commercial invoice, packing list and certificate of origin, plus whatever else the customs broker at the destination requires. Documentation is prepared before the container leaves the factory.
- • A free on-site survey is carried out before ordering to measure the door opening.
- • Production follows the dimensions and finish you approve after the survey.
- • Installation is carried out on-site by our own team.
- • Our warranty against manufacturing and workmanship defects is unlimited; an official 2-year warranty document is provided on delivery.
- • Price incl. VAT: %20 Includes VAT.
You May Also Like
Before you decide
Pages where we cover the technical questions most often asked about this model:
modern design
More Models in This Style

Geometric Diamond Orange Red Walnut Steel Door C-TR730

Diamond-Motif Dark Brown Steel Door C-TR726

Circle Medallion Dark Burgundy Brown Steel Door C-TR720

Tall Vertical Dark Burgundy Gloss Steel Door C-TR718
wood tone
Models in the Same Color Family

Three-Section Honey Walnut Steel Door C-TR731

Geometric Diamond Orange Red Walnut Steel Door C-TR730

Two-Section Paneled Dark Walnut Antiqued Steel Door C-TR729





